Items: 0 Total: £0.00

Forgotten your password?
.

 
  Home > New Products

Magneto spares

ImageNameDescriptionPriceQty 
Clutch Plate CS gearbox Sturmey Archer
Clutch Plate CS gearbox Sturmey Archer £7.70
Clutch plate outer SD/Ricardo sliver
Clutch plate outer SD/Ricardo sliverHarden and tempered spring steel clutch plates nitrogen cut out of 0.8 spring steel

price per Plate
£16.00
Clutch Plate SD and Ricardo Bronze inter
Clutch Plate SD and Ricardo Bronze interphosphor bronze sheet water jet cut to the same sizes inter plate£24.00
Early Veteran Fork Buttress  Casting
Early Veteran Fork Buttress CastingEarly Veteran Fork Buttress  Casting made from SG iron ready to be machined.£33.00
Front stand hoop
Front stand hoopFront stand hoop fits SD , Ricardo's , P and N models  £65.00
Gasket Barrel base
Gasket Barrel base

Paper gasket for the barrel Base

Veteran is 1910 to 1914

Model H,SD, Ricardo

Model P, N,NSD 

£5.00
Gudgeon pin 16mm vintage
Gudgeon pin 16mm vintage

Gudgeon pin 16mm vintage

16mm dia

76mm long

8mm bore

£10.00
Magneto Cable Model P
Magneto Cable Model PMagneto Cable Model P. Fully assembled with rubber grommet and nipple. 3 ft long.£12.10
Model P/N spanner
Model P/N spanner

Model P/N spanner 

I made this for the Cannonball run to take out plug caps and barrel off if need on the run!

£6.00
Model P/N/Q/NSD crank pin
Model P/N/Q/NSD crank pinModel P/N/Q/NSD crank pin.

Made from Aerospace grade material this pin is made to withstand hard condition.

This batch was made for the Cannonball Run across the USA and  My crank completed 4000 miles on the road running 3/4 to full throttle each day.
£110.00
nut 5/16 whit thin
nut 5/16 whit thin

nut 5/16 whit thin

5/16 whit x 1/4 wide x 0.525 hex

£2.00
Nut 5/16 whit x 0.300 wide for spring clamp bolt
Nut 5/16 whit x 0.300 wide for spring clamp boltNut for front spring clamp bolt 3/8 whit x 0.300 wide 7/16 hex£2.50
Nut Clutch spring adjuster for model P,N and NSD
Nut Clutch spring adjuster for model P,N and NSD

clutch spring adjuster nut for model P,N and NSD

1/4 x 24 tpi

6 required sold individually

£6.00
Nut SD/Ricardo Clutch nut
Nut SD/Ricardo Clutch nutNut SD/Ricardo Clutch nut£20.00
oil pump worm gear bronze
oil pump worm gear bronze

oil pump worm gear

N , N deluxe and NSD

£60.00
Oval Tubing 2 x 0.5m Rear Stand Tube
Oval Tubing 2 x 0.5m Rear Stand Tube5/8 x 1 1/8  oval  with 2mm wall thickness.

This listing is for 2 of 0.5m lengths

used for rear stands in most triumph motorbikes

Due to length of the tube, postage is too high to regularly send 1m lengths, especially abroad. We will now sell by default the tubing already cut in two. If you wish to have an uncut 1m, please contact us and we can arrange additional postage
£22.00
Pinion Gear P later
Pinion Gear P later

Pinion Gear P/N/NSD

20 Teeth 0.450 wide x 0.563 bore

£40.00
Primary cover P/N and later
Primary cover P/N and laterHand made to fit P and N will fit most model up to early NSD£330.00
Rollers for bigend 7/32 x 7/16
Rollers for bigend 7/32 x 7/16

Rollers for bigend 7/32 x 7/16 all have been hand made and ground as no longer made

standard

plus 0.0005 thou

plus 0.001 thou

plus 0.0015 thou

plus 0.002 thou

plus 0.0025 thou

plus 0.004 thou

£2.50
Spring Baby triumph kick starter
Spring Baby triumph kick starter

Spring Baby triumph kick starter after 21 when they put a kick starter and clutch on the bike

£8.00

Page
« Prev |1|2|3|4|5|6| Next »

Telephone : +44 (0) 777 3324238 
email: parts@veterantriumph.co.uk

Privacy & Cookies