Items: 0 Total: £0.00

Forgotten your password?
.

 
  Home > Model P Spares

Magneto SparesMagneto Spares

ImageNameDescriptionPriceQty 
Clutch Cable Model P
Clutch Cable Model PClutch Cable Model P - fully assembled with adjuster and nipple. 4.5 ft in length
Will fit model N ,Q, QA and early NSD
£22.00
Clutch Friction Plate Model P/N and later
Clutch Friction Plate Model P/N and laterNew clutch Plates laser cut from modern material 5 inch od  4 inch bore£19.00
Exhaust Model P
Exhaust Model PExhaust Model P comes frpnt half only.with down pipe
You can use the box to make model Q / N and NSD etc system 
£250.00
Fuel Cap 2" dia Brass
Fuel Cap 2" dia BrassFuel Cap 2" brass stamped Rotherhams Coventry.
Ready to plate.
Bayonet clip on cap.
 


Spring inside is slightly larger than some originals and can prevent the cap from closing.
Spring can be easily modified to fit. Otherwise it can be loose on repro tanks.
Cut off 2 - 4 mm of spring, Heat up till red the end of spring and push flat, Grind flat and Use.
£68.31
Fuel tank pump tube
Fuel tank pump tube15/16 bore x 1 inch od x 141mm long£40.00
Gasket Barrel base
Gasket Barrel base

Paper gasket for the barrel Base

Veteran is 1910 to 1914

Model H,SD, Ricardo

Model P, N,NSD 

£5.75
Gudgeon pin 16mm vintage
Gudgeon pin 16mm vintage

Gudgeon pin 16mm vintage

16mm dia

76mm long

8mm bore

£11.50
Handle bars Model P (Ricardo)
Handle bars Model P (Ricardo)Handle bars Model P 29 inches end to end£44.27
Magneto Cable Model P
Magneto Cable Model PMagneto Cable Model P. Fully assembled with rubber grommet and nipple. 3 ft long.£22.00
Manual 1926 Model P spares
Manual 1926 Model P sparesManual 1926 Model P spares£11.50
Model P exhaust system complete
Model P exhaust system completeFront box as photo and tail pipe ready to fit£330.00
Model P/N spanner
Model P/N spanner

Model P/N spanner 

I made this for the Cannonball run to take out plug caps and barrel off if need on the run!

£6.90
Model P/N/Q/NSD crank pin
Model P/N/Q/NSD crank pinModel P/N/Q/NSD crank pin.

Made from Aerospace grade material this pin is made to withstand hard condition.

This batch was made for the Cannonball Run across the USA and  My crank completed 4000 miles on the road running 3/4 to full throttle each day.
£126.50
Nut 1/4 whit
Nut 1/4 whitNut 1/4 whit.
Nut 1/4 whit x 1/4 wide x 1/2 hex
used on seats and other parts of bike.
£2.53
Nut 1/4 x 24 x 1/4 wide
Nut 1/4 x 24 x 1/4 wideNut 1/4 x 24 tpi x1/4 wide 7/16 hex
Magneto stay and model P bolts on crankcase and frame farts
£2.30
Nut 3/8 frame domed head  5/16 wide
Nut 3/8 frame domed head 5/16 wideNut 3/8 x 24 tpi frame domed head  5/16 wide x 600 thou hex
used on veterans also
£3.45
Nut 3/8 whit for seat and others domed head
Nut 3/8 whit for seat and others domed headNut 3/8 whit for seat and others.
3/8 whit x 3/8 wide domed end
£3.16
Nut 3/8 x  0.280 wide domed head
Nut 3/8 x 0.280 wide domed headNut 3/8 x 0.280 wide 0.6 thou hex for veteran frame bolts mainly.£3.45
Nut 3/8 x 13/32 wide domed head
Nut 3/8 x 13/32 wide domed headNut 3/8 x 24 tpi x 13/32 wide 0.6 thou hex for some frame bolts£3.45
nut 5/16 whit thin
nut 5/16 whit thin

nut 5/16 whit thin

5/16 whit x 1/4 wide x 0.525 hex

£2.30

Page
« Prev |1|2|3|4|5|6| Next »

Telephone : +44 (0) 777 3324238 
email: parts@veterantriumph.co.uk

Privacy & Cookies