Items: 0 Total: £0.00

Forgotten your password?

  Home > Model P Spares

Bearing 1163X/1120NI 9/16 bore wheel bearing
Bearing 1163X/1120NI 9/16 bore wheel bearingBearing 1163X/1120NI 9/16 bore wheel bearing.
for Triumph P and later 
9/16 x 1 3/4 x 7/8 wide
Bearing 1178X/1120NI 5/8 bore wheel bearing
Bearing 1178X/1120NI 5/8 bore wheel bearing £46.20
bearing gearbox 1 1/8 x 2 1/8 x 3/8 wide deep grove bearing
bearing gearbox 1 1/8 x 2 1/8 x 3/8 wide deep grove bearing £15.95
Bolt and nut Model P/N etc Sprocket
Bolt and nut Model P/N etc SprocketModel P/N  etc Bolt and nut to hold or rear sprocket . £8.58
Brake Block 88
Brake Block 88New brake blocks used on Model H and SD plus can be modified to be used on Model P also.

They are being sold for Display use Only and if Used for Road use are used at you Own Risk as per our terms and conditions.(because a brake insurance policy cost so much to run and would double the price)
Cable Nipple 976/1 5 off
Cable Nipple 976/1 5 off

1/4 dia x 1/8 wide used on the model P/N and later Levers

Pack off 5

Carburetor fuel nut
Carburetor fuel nutCarburetor fuel nut
9/16 X 25Tpi
Brass hex.
Carburetor needle
Carburetor needle

Carburettor needle

72.5mm suits early Model H
78.6 mm suits P and later
85mm long machine to what you need
check your size as there has been some carbs that need longer Needles and are from the wrong model also

you must set your float level one this is installed

Carburettor Float twin barrel carbs
Carburettor Float twin barrel carbsFloat Vintage twin barrel Carburettor
Brand new carb float to fit float bowls with the needle that seals in the top screw on cap.
Will fit model H,SD,P,PN,N,NSD etc
Carburettor bolt gasket
Carburettor bolt gasketCarburettor bolt gasket petrol resistant material£1.37
Carburettor fuel bowl gasket
Carburettor fuel bowl gasketCarburettor fuel bowl gasket petrol residence Material
some of the early bowls need a small amount taking of OD

I do it on the grinder on the od
casting Front stand legs
casting Front stand legsFront sand lugs bronze£7.70
Casting Model P Exhaust
Casting Model P ExhaustCasting Model P/N,Q Exhaust Hanger£13.20
Chain 1/2 x 1/8 for Magneto sold buy 300mm/ 1 foot
Chain 1/2 x 1/8 for Magneto sold buy 300mm/ 1 footChain timing 1/2 x 1/8
sold buy 300mm/ 1 foot
SD/Ricardo/H 46 links need  2 feet needed
SD/Ricardo Dyno 48 links 3 feet needed
Model P 44 link 2 feet needed
Chain 5/8 x 1/4 x 107 links
Chain 5/8 x 1/4 x 107 linksChain 5/8 x 1/4.
sold buy the box
97 links of Regina comes with one link in the box.
final drive and from engine to gearbox also

SD/P/N/Q/QA Primary 52 links

P/Q/N Rear Chain 
Solo 89 with a 38 teeth rear
side car 92 with a 43 teeth rear
Chain Guard Model P
Chain Guard Model P £110.00
Chain Link 1/2 x 1/8
Chain Link 1/2 x 1/8Chain Link 1/2 x 1/8
1 connector
Chain link 5/8 x 1/4
Chain link 5/8 x 1/4 £4.40
Champion Spark Plug 6 COM
Champion Spark Plug 6 COMChampion Spark Plug 6 COM new old stock

once their gone their gone

I used one of these plug in 2018 on the cannonball run for 3500 mile and had no problem with them fouling they run better on unleaded then champion 7 as they are a bit hotter then a 7
Clutch Basket spring cups
Clutch Basket spring cupsClutch Basket spring cups for P N NSD and will fit the later C series also£6.60

« Prev |1|2|3|4|5|6| Next »

Telephone : +44 (0) 777 3324238 

Privacy & Cookies