Other Models - Page 4

Home > Other Models

Magneto Spares

Image	Name	Description	Price	Qty
	Clutch Cable Model P	Clutch Cable Model P - fully assembled with adjuster and nipple. 4.5 ft in length Will fit model N ,Q, QA and early NSD	£22.00
	Clutch Friction Plate Model CO-CSD and Later	New clutch Plates laser cut from modern material 143mm OD 111mm ID x 2.5mm Thick	£18.97
	Clutch Friction Plate Model P/N and later	New clutch Plates laser cut from modern material 5 inch od 4 inch bore	£15.81
	Clutch plate CO-CSD steel	steel clutch plate CO-CSD laser cut	£18.97
	Exhaust Model P	Exhaust Model P comes frpnt half only.with down pipe You can use the box to make model Q / N and NSD etc system	£250.00
	Footrest hanger N/NSD	Footrest hanger N/NSD made as per the original ones from CDS steel 3mm wall thickness with steel insert / bar	£126.50
	Fuel Cap 2" dia Brass	Fuel Cap 2" brass stamped Rotherhams Coventry. Ready to plate. Bayonet clip on cap. Spring inside is slightly larger than some originals and can prevent the cap from closing. Spring can be easily modified to fit. Otherwise it can be loose on repro tanks. Cut off 2 - 4 mm of spring, Heat up till red the end of spring and push flat, Grind flat and Use.	£68.31
	Gasket Barrel base	Paper gasket for the barrel Base Veteran is 1910 to 1914 Model H,SD, Ricardo Model P, N,NSD	£5.75
	Gudgeon pin 16mm vintage	Gudgeon pin 16mm vintage 16mm dia 76mm long 8mm bore	£11.50
	Handle bars Model P (Ricardo)	Handle bars Model P 29 inches end to end	£44.27
	Manual Model N and QA spares	Manual Model N and QA spares	£11.50
	Manual Model Q and QA spares	Manual Model Q and QA spares	£11.50
	Manual Gloria side car spares	Manual Gloria side car spares	£11.50
	Model P/N spanner	Model P/N spanner I made this for the Cannonball run to take out plug caps and barrel off if need on the run!	£6.90
	Model P/N/Q/NSD crank pin	Model P/N/Q/NSD crank pin. Made from Aerospace grade material this pin is made to withstand hard condition. This batch was made for the Cannonball Run across the USA and My crank completed 4000 miles on the road running 3/4 to full throttle each day.	£126.50
	Nut 1/4 whit	Nut 1/4 whit. Nut 1/4 whit x 1/4 wide x 1/2 hex used on seats and other parts of bike.	£2.53
	Nut 1/4 x 24 x 1/4 wide	Nut 1/4 x 24 tpi x1/4 wide 7/16 hex Magneto stay and model P bolts on crankcase and frame farts	£2.30
	Nut 3/8 frame domed head 5/16 wide	Nut 3/8 x 24 tpi frame domed head 5/16 wide x 600 thou hex used on veterans also	£3.45
	Nut 3/8 whit for seat and others domed head	Nut 3/8 whit for seat and others. 3/8 whit x 3/8 wide domed end	£3.16
	Nut 3/8 x 0.280 wide domed head	Nut 3/8 x 0.280 wide 0.6 thou hex for veteran frame bolts mainly.	£3.45

Page
« Prev |1|2|3|4|5|6|7| Next »